Call Us Free: (+91) 946-661-0761

Product Details

COMPLETE LINE

COMPLETE LINE

 
Fruit juice is a very healthy food. It consists of water, fruit sugar, fruit acid and minerals. Depending on the type of fruit, juice contains different vitamin concentrations. Due to its high water content, juice is very susceptible to micro-organisms and must be processed very carefully and hygienically.

 Commercially Available Fruit Juice Categories:

Direct Juice: it is pressed and processed directly.

Juice: some of the water is removed from the juice for transportation and is added again to the same extent before bottling. No other ingredients are added. The quality of the juice only depends to a slight extent on whether not the end product contains fruit pulp.

Nectar: does not have the full juice content, only 25% to 40% is fruit juice. The product is diluted with more water than was removed from the original juice. Other ingredients are added at times.

Fruit Juice Drink: a fruit juice drink has more sugar than fruit juice. In this case the drink must only contain between 6% and 30% as fruit juice.
Now-a-days, an increasing number of drinks containing a mixture of fruit juice are being launched on the market.

Fruit Juice Production:
Fruit juice production is divided into two steps:

1. Juice Extraction: Juice extraction is done by mechanically squeezing the fruits without using any heat or solvent. Extracted juice is then directly fed into bottling unit or concentrated for later use or to sell to other customers. The advantage of concentrated juice is that it requires less space and thus less refrigerating capacity. Some juice producer uses concentrated juice as raw material instead of fresh fruits.

The juice yield fluctuates between 40% and 85% of the fruit weight, depending on the fruit. The conductivity of juice ranges between 2.0 and 16.0 mS/cm. Juice extraction is a seasonal business: it is restricted to a few periods during the year. However, the full plant capacity has to be available during these periods. This places high demands on the technology. Stoppages may lead to spoiling of the fruit and subsequently to high losses. Once the concentrate has been produced, it must be preserved and documented in order to maintain the cooling chain up until final use.

 2. Juice Bottling: The juice is adjusted in the bottling plant with water to reconstitute the liquid back to its "original state". It may be necessary to mix different batches in order to obtain a constant taste. Different fruit juices are also frequently mixed. Up to 15 grams of sugar, or even more in the case of some citrus fruits or citric acids, may be added per liter. The added ingredients must be shown on the label. There are two types of bottling is available for fruit juice: Hot filling & Aseptic Process.
 
 PET BOTTLE PACKAGING 100 ML-2500 ML
 

 

 
 GLASS BOTTLE PACKAGING 100 ML-2000 ML


  
PET BOTTLE WITH SPORTS CAP TYPE PACKAGING 100 ML-2000 ML


 
 
 HDPE BOTTLE WITH CAP PACKAGING 100 ML-500 ML


 
 HDPE BOTTLE WITH TOP ALUMINIUM FOIL SEALING PACKAGING 100 ML-500 ML

 
SPOUT POUCH PACKAGING 50 ML-500 ML


 
 
 COMPLETE TURNKEY PROJECT FOR FRUIT JUICES & SYNTHETIC DRINKS. 
Our Turnkey Project Includes Design, Supply & Commissioning of Juice Line, which includes, Water Treatment System, Juice Processing & Blending Section, Bottle Blowing Machines, Bottle Filling Machines, Date Printers, Labelling Machines & Shrink & carton Packing Machines. Capacity available from 500 LPh till 1,00,000 LPH.
  
MINERAL WATER TREATMENT SYSTEM FULLY SS-316 
The processing flow adopted by a set of water treatment system depends on quality of water source and target purpose of water usage. The selected flow basically includes three parts: pretreatment system, micro processing system and final processing system. The Pretreatment system includes multi-media filter, active carbon filter, softener, iron-manganese removal filter, ultra-filter, micro-filter, etc. The micro processing system adopts membrane filtration and ion exchange method. The final processing system involves in ozone/UV sterilization, iron exchange etc.
 
 

 JUICE PREPARATION, MULTIBLEND & MIXING SYSTEMS 
Designed concentrated Pulp and essences are processed at the concentrate and powder-dissolving stations, and the food-grade acids in crystalline or powder form are also dissolved here.

Agitation and mixing devices are used depending on the viscosity of the components, the batch size and the solubility.
By storing at ambient temperature, in insulated storage vessels, the character and aspect of freshness when the fruit pulp is processed, are both preserved exactly in accordance with individual production requirements.

After the Concentrated Pulp is Processed & sugar is dissolved into the juice , it’s the time to Homogenize & Pasteurize Juice & fill at a High Temperature to minimise bacterial growth and maximize Shelf life of the Product.

 

 
  
HOMOGENIZER

 
 
JUICE PASTEURIZER

 The Automatic plate sterilizer is suited for liquid food products including fruit Juices, milk etc.. Scientific technology of instant ultra high temperature, 135-143°C for 4-5 seconds, is adopted to achieve commercial sterility . By which there would be little adverse effect on the product quality such as little nutrition and flavor losses. The shelf life of product dealt by the machine may be 6-12 months.Specifications:Production capacity: 0.5~20MT/hSterilization temperature: 137°CHolding time: 5~15sControl modes: semi-automatic, automatic (PLC control, touch screen display system)
 

 
AUTOMATIC PET BOTTLE BLOW MOULDING MACHINE 

MECHSYS manufactures excellent quality Automatic PET Blow Moulding Machines for PET bottle production. Our Automatic PET Blow Moulding Machines have wider wide-mouth capability, faster production rates, and shorter changeover times. Also have features such as preferential heating or heat-setting capability. Our Two stage Plastic PET machines can make bottles from round to flat bottle styles. With our two stage Automatic PET Blow Molding Machines you can produce various different shaped PET containers, such as mineral water bottle, beverage bottle and many more types of Plastic PET Bottles.
Machine Supplied with High & Low Air Pressure Compressor with Mould, Cooling Tower, Air Dryer and Air Filter with other utilities All pneumatic systems are Festo Brand

 

 

 FEATURES

1).High Automatisation Fully controlled with Servo Drives & directly connect with Air      conveyor to connect with Filling Machine to transfer bottles from blower to filer.
2). More Advanced: Advanced PLC control system with a use-friendly Control Panel which has Fully Equiped Touch Screen control.
3).High Quality: Steady infrared heating system blowing and highly precise blow-mould  closing system ensure quality.
4).High Speed: 2400BPH (2-cavity), 4200BPH (4-cavity), 6600BPH (6-cavity), 8400BPH (8-cavity).
5). Quick Mold Change-Over using Mold Cage System.
6).Low Cost: Low consumption of electricity, air and water.
7). Power Equipped Machine using Air Recovery System

 

 MOULDS
 


6 Cavity Diamond Polished Pet Blow Moulds.


AIR CONVEYOR SYSTEM :

1. Empty bottle Conveying system-Air Conveyor: Our specialized design is applicable for  the transfer of empty PET bottles from Blowing Machine to Filling Machine       Automatically.

2.Full Structure made of SS 304 & Air Blower also made from SS 304 Food grade material to avoid Contamination of bottles due to rust from normal MS Blowers. 

3.Air filter is attached with the Blower in order to remove dust & unwanted Particles which can cause Contamination, It also equipped with Noise reduction system to reduce Noise.

4.It also provides filling equipment with a certain quantity of reserve bottles during any problem or temporary breakdown of Blowing Machine.
 

 
Various shapes of Air Conveyors are available like Straight, Round, ‘U’ Shape & ‘Y’ Shape. According to the Space & Requirement of the client we design the system.
 

AUTOMATIC PET BOTTLE RINSING FILLING & CAPPING MACHINE

Our Specially Designed RFC Machine are based on Latest Design & Technology used for Bottling of Pet bottles with Maximum Automation.

 

 

 

Features Of Rinsing Filling & Capping Machine.

  • The machine is fully neck-run and infeed is by air conveyor.
  • There are only two change parts namely the capper star wheel and infeed star wheel, and resetting machine to different size of bottle will take only 30 minutes.
  • There is no height setting requirement during changeover.
  • The complete R.F.C is enclosed in transparent plastic and stainless steel guard cover without any rubber gaskets. This ensures there is no bacterial growth in the crevices.
  • The electrical panel is IP 55 grade and has user-friendly mimic panel. Mimic diagram with red, green, yellow LED indicates machine status, safety indication and normal operation. Merely by monitoring the LED indications, operator can diagnise the fault condition.
  • There is central lubrication system, which supplies to all vital components. Also manual grease points located in easy to access centralized grease banks.
  • The entire R.F.C machine is constructed in stainless steel above the table top leve
  • Speed Available from 30 BPM to 600 BPM. 6 Fillng Nozzles to 100 Filling Nozzles.

NECK HOLING SYSTEM:
 
OUR SPECIALLY DESIGNED RFC MACHINE ADOPTS NECK HOLDING TECHNIQUE FOR ALL OPERATION LIKE BOTTLE TRANSFER DURING DIFFERENT SECTION OF BOTTLE RINSING, FILLING & CAPPING. WHICH REDUCES ANY CHANGE OVER PARTS FOR DIFFERENT SIZES OF BOTTLES.

 

RINSER SECTION

The rinser washing nozzles work under positive pump pressure of de-mineralized water, but can also be designed to use ozonized air or a cleaning agent. The bottle is inverted 180° in the rinser to ensure that the cleaning agent is drained before reaching the filler.

  • The rinser has a No Bottle-No rinse arrangement which prevents wastage of water.
  • The important feature on the R.F.C. is water saving, one can recover 90% of rinse water
  • by collecting in a dump tank and recycle it by sending to the raw water storage tank.
  • There is no chance for contamination by oil, grease and other contaminants from the
  • machine as the rinse water is at all times passed through and is in contact only with
  • stainless steel components, this includes the rinse water after use.
  • The rinser has minimal water wastage and recycles rinse water but ensures a high level of cleaning and so is a economical and eco-friendly machine.

FILLER SECTION

The Filling valves work on the gravity principle, the water is supplied to the filling tank by a centrifugal pump, and the water level in the tank is controlled. The bottles are raised to the filling nozzle by positive lift cylinder, if the bottle is not delivered the valve does not open. The water will be filled to pre set level and the bottle is lowered.

 

The lift cylinders operate on positive cam lift-off principle and do not use compressed air or spring load. Lift cylinder cam is made of stainless steel and machined to fine finish and have simple harmonic motion profile to lift bottles smoothly to filling valve. The filling valve works on gravity filling system but has AIR EXHAUST system which removes stagnant air from the bottle to outside atmosphere and do not allow bottle air to mix with ozone atmosphere in filler tank. The top of the filling bowl/tank is fitted with central manifold to connect all filling valves to single line vent pipe, which can be piped to outside of the filling room. To the same vent pipe reverse flow CIP liquid is connected by isolation butterfly valve. The filling bowl is fitted with Electro-Magnetic type level controller to regulate water level in the bowl through pneumatic ON-OFF valve.

•The vent tube is adjustable so the fill level in the bottle to be set as per the individual shape of the bottle

CAPPER SECTION:

The bottle is then transferred to the pick and place type screw capper. Here the cap is picked up by the adjustable torque chuck and firmly tightened onto the bottle mouth. The capping chucks are finest quality precision component fitted with magnetic torque controlling coupling. This eliminates heat generation which normally occurs in friction type coupling in the chucks Flexible segmented cap holder picks up the caps. This compensates minor variation in cap diameter occurring due to long storage of caps in boxes.

The capping torque can be set between 8 to 16 inch pound with minimum of time and set torque is maintained consistently. The cap delivery chute has a built-in cap washing system. The cap will not be picked up if there is no bottle hence there will be no wastage of caps.

CAP ELEVATOR

  • The cap delivery is from a hopper based on the ground level making loading of caps easier and also ensures the cap is delivered the right side up to the cap rinsing system.
  • The capping turret is of a pick and place type which delivers the cap to the holder, this leads to improved cap tightening at high speeds.
  • There is a cap rinser in the delivery chute from the hopper to the capping star wheel that insures any contaminants during storage of the cap are removed.
  • The elevator cap hopper is placed on the floor level and so makes material handling and cap loading easier.
  • The chute from hopper to capper has sensors in place to ensure that when the chute is full elevator motor stops. If the caps are not delivered till low level of chute- the machine will stop and show alarm signal on panel.
  • There is a no bottle- no cap system in place to prevent wastage of caps.
  • There is an ejector mechanism in each capping chuck in case the cap is picked up when there is no bottle.
  • Prevents Breakage of Seal of cap as in case of rotary cap Sorter.
  • Prevents Plastic dust due to Friction between caps during sorting.

AUTOMATIC BOTTLE COOLING TUNNEL

The fully automatic bottle cooling tunnel is used for cooling of hot filled Fruit Juice drinks in PET or Glass Bottles of Various sizes for a minimum temperature reduction of 50°C up to a maximum of 70°C to ensure no deformation of PET bottle. The output of the tunnel is limited to 15% more than the rated filler speed for bottles and has a capacity to hold 10 minutes accumulation of the these bottles with filler running at its rated speed. As such any size of Bottle Cooling Tunnel can be supplied depending on user's specific requirement.

  

 


 

After Cooling of the Bottles, they are suitable for date coding & labeling & Packaging in Cartons or Shrink Wrap.

 

AUTOMATIC PVC SHRINK SLEEVE APPLICATOR 

 

MECHSYS revolutionizes in-line, mandrel-style shrink film application. Its innovative design relies on a common structural frame and a modular control platform from Rockwell Automation, which enables plug n' play functionality for customization of specific end user applications. Benefits of the machine's integrated design include servo-driven precision, quick & easy maintenance, hassle-free upgrades and straightforward data feeds to the end user's business systems. The latest models utilize the programming standard, which simplifies operation, maintenance and line.

 

FEATURES:

  • Fully automatic operation.
  • No Bottle - No Sleeve-Feature (eliminates wastage).
  • Rotary cutting system.
  • Can handle round glass / plastic bottles.
  • Speed of 40 bottles to 600 bottles/min. depending on the cut length of the sleeve.
  • Servo motors for more accuracy.
  • Fitted with digital PLC control & Touchscreen.
  • Height adjustments to suit height variant bottles.
  • Eye mark sensor for accurate cutting in printed sleeves.
  • VFD used to increase or decrease the speed wherever necessary.
  • Can easily be synchronized with a tunnel.

STEAM TYPE SHRINK TUNNEL

  • MECHSYS Newly designed steam tunnel system precisely focuses steam onto
  • specific points of the shrink-sleeved packages. The tunnel has symmetrical steam
  • distribution tubes on each side, and each pair of tubes is adjustable for
  • steam volume. Adjustments can be made "in real time,"
  • without wasting time – and energy – waiting for the tunnel to cool down.
  • A thermostatically controlled steam chamber, available as an option, generates the
  • most energy-efficient steam system possible. Unlike straight pressure systems,
  • which waste energy by pumping large volumes of steam into the tunnel without
  • electronic regulation, Our unique control system uses only the steam required to
  • maintain chamber temperatures and provide optimal shrink quality.

It provides precise label registration, distortion-free graphics, and exceptional conformance to the container shape. The system virtually eliminates the risk of container distortion.  

PVC, PETG, OPS and PLA films, in gauges as thin as 40 microns, are all compatible.

 

AUTOMATIC SHRINK WRAPPING  MACHINE WITH SHRINK TUNNEL

          

It is specially used for packing bottle water, juice, wine, beer, etc. It uses plastic film for packing bottle water. It includes Automatic packing machine and Heat Shrink machine. Shrink Wrapping Machine is equipped with transducer, which can adjust various speeds for packing bottle water. Shrink Tunnel has double-cycle system, which can save cost and assure the packing quality. The cutting system abides by international rules and with best sealing quality.

FEATURES:

  • Fully automatic operation.
  • Efficient Sealing & Cutting Blades used.
  • Can handle Bottles with or without Tray
  • Speed of 8-10 Packs/min. depending on the No of Bottles per pack.
  • Fitted with digital PLC control & Touchscreen.
  • Height adjustments to suit height variant bottles.
  • Temperature Controllers Provided for Shrink Tunnel for adjustment while switching to different size.

Back to Top